ATV & UTV 2019

STEERING & SUSPENSION 1114 body accessories handlebar & grips cables & levers engine fuel & intake carriers & racks plows & implements frame & chassis utv accessories bumpers & winches electrical & ignition clutch brakes drive steering & suspension bearings tires & wheels chemicals tools & shop exhaust dealer aids HIGH LIFTER ATV LIFT KITS continued MAKE/MODEL YEAR * PART # YAMAHA Bear Tracker 250 4x4 99 - 04 254064 155.95 Big Bear 350 4x4 95 - 96 4563540 86.95 Big Bear 350 4x4 97 - 99 4563541 86.95 Big Bear 400 2x4 01 - 04 4564002 119.95 Big Bear 400 4x4 12 4564003 139.95 Big Bear 400 4x4 00 - 06 4564002 119.95 Big Bear 400 4x4 IRS 07 4564003 139.95 Bruin 350 4x4 04 - 06 4564001 124.95 Grizzly 450 4x4 07 - 12 4564501 159.95 Grizzly 450 4x4 13 - 14 254067 164.95 Grizzly 450 EPS 14 254067 164.95 Grizzly 550 4x4 09 - 14 ----- Grizzly 550 4x4 09 - 14 78 254104 118.95 Grizzly 550 4x4 EPS 14 ----- Grizzly 550 4x4 EPS 14 78 254104 118.95 Grizzly 600 4x4 98 - 01 4566000 142.95 Grizzly 660 4x4 02 - 08 4566600 84.95 Grizzly 660 4x4 02 - 08 76 4567001 127.95 Grizzly 700 4x4 07 - 13 ----- Grizzly 700 4x4 07 - 15 78 254104 118.95 Grizzly 700 4x4 16-18 79 254143 118.95 Grizzly 700 4x4 EPS 14 - 15 78 254104 118.95 Grizzly 700 4x4 EPS 16-18 79 254143 118.95 Grizzly 700 4x4 LE 16-18 79 254143 118.95 Grizzly 700 4x4 SE 16-18 79 254143 118.95 Kodiak 400 2x4 00 - 04 4564001 124.95 Kodiak 400 4x4 99 4563541 86.95 Kodiak 400 4x4 95 - 98 4563540 86.95 Kodiak 400 4x4 00 - 06 4564001 124.95 Kodiak 400 4x4 05 - 06 75 4564500 114.95 Kodiak 450 4x4 03 - 04 4564001 124.95 MAKE/MODEL YEAR * PART # YAMAHA CONTINUED Kodiak 450 4x4 05 - 06 75 4564500 114.95 Kodiak 450 4X4 18 90 254324 119.95 Kodiak 450 4X4 EPS 18 90 254324 119.95 Kodiak 700 16-18 80 254144 118.95 Kodiak 700 EPS 16-18 80 254144 118.95 Kodiak 700 SE 16-18 80 254144 118.95 Rhino 450 4x4 07 - 09 77 4566602 119.95 Rhino 660 4x4 07 77 4566602 119.95 Rhino 660 4x4 04 - 06 45666007 114.95 Rhino 700 4x4 08 - 13 81 4567003 124.95 Timberwolf 250 4x4 95 - 99 254063 149.95 Timberwolf 450 4x4 95 - 99 254063 149.95 Viking 700 14 - 18 82 254092 165.95 Viking 700 EFI 15 82 254092 165.95 Viking 700 EFI SE 14 82 254092 165.95 Viking 700EPS Ranch 18 82 254092 165.95 Viking 700 EPS 14-18 82 254092 165.95 Viking 700 EPS SE 16 - 17 82 254092 165.95 Viking 700 VI 15 - 17 82 254092 165.95 Viking 700 VI EPS 15-18 82 254092 165.95 Viking 700 VI EPS SE 15-17 82 254092 165.95 Viking 700 VI Ranch 16-18 82 254092 165.95 Wolverine 16-18 83 254094 179.95 Wolverine R-Spec 16 83 254094 179.95 Wolverine R-Spec EPS 16-18 83 254094 179.95 Wolverine X4 18 91 254325 219.95 Wolverine X4 SE 18 91 254325 219.95 YXZ 1000 R 17 84 254248 TBA YXZ 1000 R SS 17 84 254248 TBA YXZ 1000R SE 16 84 254248 TBA NOTES: 1 NOTE: does not fit trv models NOTE: 1" spacers are required on the rear if you run factory wheels with a lift kit installed. Key features: * 3” signature series lift * laser cut 3/16” steel brackets * aluminum high lifter name plate * heavy duty alloy steel tie rod * allows 31” tires 2 Does not fit ac500i 2005 models!!!!!!! See part# alk650-00 for 2006-2007 ac500i models!!!! 3 Notes: 1" spacers are required on the rear if you run factory wheels with a lift kit installed. 4 NOTE: does not fit prowler 700 hdx. 5 Signature series lift kit NOTE: if running rear outlaw dht axles and this lift kit, you need to remove the rear axle spacer as shown in the instructions. If running this lift kit with rear stock axles, the rear axle spacer is still needed. Please refer to the instruction manual for further information. NOTE: does not fit any outlander max or outlander & renegade xmr models!!!!! The front axles bind and the boot rubs on these models. 6 Signature series lift kit 2017 modles will not work due to changes in the rear trailing arm!!!! NOTE: the front portion of this lift consits of 1" spring spacers only. The rear is a bracket lift. NOTE: if running rear outlaw dht axles and this lift kit, you need to remove the rear axle spacer as shown in the instructions. If running this lift kit with rear stock axles, the rear axle spacer is still needed. Please refer to the instruction manual for further information. 7 Can Am Outlander 1000 signature series lift kit - 2017 lift amount: 1-1/2” install time: 2 hours largest tire 28” -- using a rear trailing arm 29.5" NOTE: this is a spring spacer only kit. 8 Lift kit CAN-AM 800/1000 commander signature series 2” lift kit-see all notes before selling! Lift amount: 2" estimated install time for experienced mechanic: 2hr NOTE: does not fit commander 1000x model with fox shocks NOTE: does not work with air ride suspension NOTES: 9 Lift kit CAN-AM 800/1000 commander-signature series 2" lift kit-see all notes before selling! Lift amount: 2” estimated install time for experienced mechanic: 2hr NOTE: does not fit commander 1000x model with fox shocks 10 Lift kit CAN-AM defender 1000/800 lift amount: 2" install time: 2 hours requires 1"pacers in the rear when running factory wheels largest tire: 27" & 28" will fit with slight rubbing largest tire with front forward kit: 31"and 1" spacers with factory wheels. Zinc plated finish. NOTE: this is not a signature series lift kit 11 Lift kit CAN-AM Maverick 2" lift NOTE: this kit does not fit 2014 CAN-AM Maverick 1000 models!!! Zinc plated finish. NOTE: this is not a signature series lift kit 12 Lift kit CAN-AM Maverick 2" lift 2017 models have a new sway-bar on the front. We need to validate the installa- tion before selling to 2017 models!!!! NOTE: for turbo models see new kit comming soon!! NOTE: this kit does not fit 2013 CAN-AM Maverick 1000 models!!! Zinc plated finish. NOTE: this is not a signature series lift kit 13 Lift kit CAN-AM Maverick 4" signature series lift kit. NOTE: this kit does not fit 2014 CAN-AM Maverick 1000 models!!! Hammertone black powdercoat finish our 4" signature series lift kit for the CAN-AM Maverick 1000 takes utv lift kits to a new level of strength and durability. The front lift brack- ets are precision welded from ¼" american-made steel, while the rear plates are crafted from 3/8" american-made steel. Each part in the kit is precision cnc laser cut, cnc bent, and cnc machined - a guarantee that your kit will fit just like our engineers designed it to be. In addition to the heavy-duty steel used in our brackets, our research and development team crafted new offset sway bar linkage that allows us to achieve additional lift without removing the sway bar. When combined with the heavy duty heims on the offset sway bar link, we’re able to achieve a 4" lift using stock axles - something the competitors cannot do!"